The filter of the exhaust hood canopies is placed in the location over your gas range. Its primary objective is to stop the generation of soot, grease and other food items to clean the air. Many people do not realise that these components must be cleaned regularly to prevent harmful air pollutants in the home. You can effortlessly clean your purification device by submerging it in a mixture of baking soda and soap water or rubbing them with a good detergent. We have written about a couple of methods in the following lines. Irrespective of the technique you employ, it is essential to ensure that you eliminate any buildup particles to get rid of any debris or soot that slowly collects in the purifier by taking care of them every month.

Commercial Gas Stoves are one of the appliances that make the task of the canopies effortless. These offerings are available for every large & small food establishment and prove efficient. Go to the Simco web page for further details.

Soak the Purifier in a Combination of Baking Soda and Liquid Dishwasher  

  • Take out the component from the machine. The technique for uninstalling the hood range filter may be distinct depending on the type and model, but they are all relatively simple. A few variants use screws for installation, while many latest models possess a user-friendly latching procedure that you can remove by pressing and lifting. Many purifiers have a clasp whose position you can change by rotating in and out. Closely monitor how your filter is attached, and remove it before cleaning.
  • If your product is covered with the help of a plastic casing, you'll need to use a screwdriver to first take that out before removing the purifier. You can contact Simco – the leading exhaust hood canopies supplier in Sydney & Melbourne – for further clarity.
  • Use water heated at a high temperature to fill your basin. Ensure to use a sink stopper to prevent the water from going down the drain. Try only to use warm water and ensure it is as hot as possible. It is best almost to fill the basin and leave only one-fourth of it empty.
  • If tap water doesn't get hot enough, boil it in a tea kettle or pot and then pour it into the sink.
  • Put one-fourth cup or 60 grams of baking soda into the basin after correctly measuring it with a dash of dish detergent. Once done, take a degreasing soap and integrate almost 15 ml or one tablespoon quantity of it into the mixture. Start combining all the ingredients and mix them until the water is foamy.
  • Employ a brush to mix the baking soda combination, mainly if you used boiling water, to avoid burning your hands.
  • If you want additional cleaning power, add one-fourth cup or 59 ml of vinegar to the mix.
  • Immerse the purifier of the exhaust hood canopies for sale in the basin and allow it to submerge for 10-15 minutes. If possible, ensure it is fully submerged, so the entire filter gets cleaned at once. Let the purifier soak in hot water for a minimum of 10 minutes to let the baking soda and dish soap break the stronghold of tough stains.
  • If your product is significantly larger than usual and is unable to adjust in the sink, it is recommended to take one-half of your purifier and maintain it before moving on to the other half.
  • Use a soft scrubbing brush to cater to the filtering device adequately. Ensure the appliance is still in the sink while scrubbing it to eliminate debris and dirt. Ensure that the item is entirely spotless by dutifully cleaning the entire surface from the front and back.
  • Open the tap, put the purifier under the water and rinse it properly. While you wash the purifier, switch on the hot water after draining the basin. Remove all the dish soap and baking soda used earlier with the help of running water. Once you wash the filter correctly, comprehensively dry it with the help of a clean fabric.
  • If you think your product needs extra time for drying, keep the device on a towel or dish rack for almost an hour.
  • Ensure that the filter is dry when you replace it in the exhaust hood canopy. In addition, ensure washing the products every month to keep them well-maintained. This process will keep your premium offering running efficiently and make it last longer.

Apart from Hoods, there are numerous options for cooking ranges in our catalogue. One of the items are Commercial Gas Griddles, the best bet for shallow frying delicate food items. For more details, visit the Simco website.

Soaking the Filters in Ammonia

  • Use a gallon-sized resealable plastic bag to spread ammonia over the purifiers. Put the items into the bag and cover them by spreading enough ammonia over them or filling the bag half full. Once done, leave the bag on a flat surface like a table after closing it.
  • You can easily limit the spread of the ammonia smell by keeping the filters with ammonia sealed in the bag.
  • Allow the purifiers to submerge in ammonia for one night. The ammonia will slowly loosen the hold of grease on the product and clean the filters while they are submerged. If you can’t leave the filters overnight in ammonia, it is recommended to keep them for at least 8 hours.
  • You don’t need to profusely rub the components or fiddle with them while they are soaked in ammonia, as you have to wash them to make them clean.
  • Let the purifiers dry after washing them under warm water. To reach this stage, use a sink to remove the filters from the bag once the scheduled time is over. Put them into the basin and turn on hot water. Ensure to remove all the ammonia from the device by rinsing correctly. Once all the above-mentioned processes are completed, put the purifiers on a dry and clean paper towel and allow them to air dry. For further information, visit Simco – the foremost exhaust hood canopies supplier in Perth & Brisbane.